Starrett 665 Inspection Holder and Dial Indicators
This is the most versatile dial indicator holder with an extremely stable base that is 8-1/2" (215mm) long x 2-1/4" (57mm) wide at the bottom. It can inspect workpieces on the top surface of the ground base or within a working area defined by the 8" (200mm) upright base post and the 9-1/2" (238mm) long gage-holding rod. The base post can be conveniently located anywhere along the 8-1/2" (215mm) T-slot in the base.
This tool can be held in a vise or by a bolt in a machine T-slot coming up through one of the two 3/8" (9.5mm) holes in the base and fastening down on the top surface.
Swivel Post Snug 665D
Snug has a .375" (9.5mm) hole for the gage holding rod and a .465" (11.8mm) hole for the upright post. Also comes with the 665L Reducing Bushing (J) that can reduce the .465" (11.8mm) hole to 3/8" (9.5mm).
Three very useful inspection combinations can be made by removing the complete swivel post snug and gage holding rod as follows:
Clamp 665G
Take the clamp and put the clamp post into the snug and lock it. Now this combination can be used to clamp the gage holding rod and the indicator into hard-to-reach places for inspecting jigs, fixtures, lining up work on centers and machine tables.
The clamp has a 3" (75mm) capacity and a post with an approximately 5-3/4" (145mm) length. The clamp post is .464" (11.8mm) diameter that fits into the regular swivel post snug 665D.
Three other clamp post diameter options available – 665G-3/8 is a 3/8" (9.5mm) diameter clamp post that can be used in the regular swivel post snug 665D with the addition of the 665L reducing bushing. The 665G-5/16 (7.9mm) and 665G-1/4 (6.3mm) can be used with other snugs to hold an indicator.
Tool Post Holder 665H
Put one end of the offset arm into the swivel post snug 665D (with the 665L reducing bushing in it). Then put this rectangular tool post holder 665H onto the other arm. This combination now allows for a good, tight setup in lathe tool posts and other machine setups.
Offset Arm 665G-1
Another very popular measuring combination is to put the reducing bushing (which is furnished) into the snug and then put one leg of the offset arm into it. Now the tool can be used in a 3/8" (9.5mm) chuck or collet to sweep a large area.
*For more details on each item, copy the Item Number below into the search bar at the top of the page.
For more info, visit www.p65warnings.ca.gov.
Item Number | Description | Price | Quantity |
---|---|---|---|
665A | Base Inspection Holder | $ 229.95 | |
665G | Clamp with .464" X 5-3/4" Post | $ 99.95 | |
665JZ | Dial Indicator (25-131J Inch Reading Indicator in Case) and Base Inspection Set | $ 975.00 | |
665MJZ | Dial Indicator (25-181J Millimeter Reading Dial Indicator in Case) and Base Inspection Set | $ 899.95 | |
PT06784-A | Gage Holding Rod with Clamp Mechanism, 3/8" x 9-1/2" (9.5 x 240mm) | $ 79.95 | |
665G-1 | Offset Arm, 3/8" (9.5mm) Diameter 3" and 5 1/2" (75 and 140mm) Arm | $ 36.95 | |
665L | Reducing Bushing Only for Swivel Post Snug | $ 14.95 | |
665D | Swivel Post Snug with 665L Bushing | $ 84.95 | |
665H | Tool Post Holder for use with 665 Inspection Sets | $ 42.95 | |
665B | Long Gage-Holding Rod | $ 89.95 |